manualshive.com logo in svg

SAVE MARINE H240, Installation Manual

Share
Download
SAVE MARINE H240 Installation Manual Download Page 41

11 

 

Save Marine, a division of 

Save innovations 

3 rue des arts et métiers, 38000 Grenoble, France   I   +33 (0)4 58 00 34 66   I   [email protected]

 

 

2.4

 

 « Contact » tab 

 

 

 

This tab gives Save Marine contact details 

 

 

 

3

 

Maintenance 

 

The materials used to manufacture the hydrogenerator are marine environment 
compliant. However, we recommend to rinse the hydrogenator with fresh water when not 
used for a long period.  

 

Algae deposition is possible on the immersed parts of the hydrogenerator.  A regular 
cleaning will maintain the system in good working conditions. We recommend using a 
cleaning product like “Clean Boat Polyvalent”. 

 

Check on a regular basis that the home plate, through-hull and hydrogenator support 
screws are correctly tightened. 

 

Check on a regular basis that the charge status of your battery is not too low, it would 
then not be able to communicate with the regulator. 

 

A storage and transportation bag is supplied with the hydrogenerator. 

 

 

 

 

Summary of Contents for H240













































Reviews:

No comments

Brands by name

Popular brands

Load more brands