manualshive.com logo in svg

SAVE MARINE H240, Installation Manual

Share
Download
SAVE MARINE H240 Installation Manual Download Page 20

10

 

 

Save Marine, a division of 

Save innovations 

3 rue des arts et métiers, 38000 Grenoble, France   I   +33 (0)4 58 00 34 66   I   [email protected]

 

4

 

Installation of the various elements 

 

4.1

 

Installation of the home plate 

Only after completing the necessary verifications and pre-installation checklist. 

The home plate must be fixed on a rigid and flat transom. If not flat, it should be 
compensated not to stress the home plate when one tightens the screws. Use for that 
whashers or holds. 

Identify the location outside the boat 

 

Check inside the boat that the location allows 
to set the counter plate and check access to 
the screws. 

 

Drill a hole with a drill Ø6 and screw  
Mark the 6 other holes. Drill using the home 
plate as a drilling template. 
Do not drill the hole for the guard locking pin  

 

Put sealing paste: 

-  on the back of the home plate  and around 

screw holes 

- on the counter plate 

 

Clean and degrease the home plate locations 

 

Outside the boat, position the home plate on 
the transom, insert the 7 M6x25 screws 

 

Inside the boat, insert the counter plate 
through the M6x25 screw until it contacts the 
inner wall. Insert the 7 M6 washers on the 
screws M6x25. Screw the bolts on the 7 M6x25 
NYLSTOP M6 screws. 

 

Summary of Contents for H240













































Reviews:

No comments

Brands by name

Popular brands

Load more brands