manualshive.com logo in svg

SAVE MARINE H240, Installation Manual

Share
Download
SAVE MARINE H240 Installation Manual Download Page 33

3 

 

Save Marine, a division of 

Save innovations 

3 rue des arts et métiers, 38000 Grenoble, France   I   +33 (0)4 58 00 34 66   I   [email protected]

 

 

This manual describes the different modes of operating of the H240 hydrogenerator. It is 
consecutive to its installation on the sailboat. See the relative booklet. 

The use of the hydrogenerator must follow the 

limits and conditions for using 

described 

in the relative booklet. 

The different parts are listed and described on the diagram on page 4 of the 

installation 

guide

.  

 

 

1

 

Handling and management of the hydrogenerator 

 

1.1

 

Placing in the home plate 

Place the H240 in front up of the home plate.  

Slide the hydrogenerator in the home plate by pulling the white rope in order to 
release the guard locking pin. 

Check that the guard locking pin is well fitted into the home plate.  

 

 

 

 

Place the H240 in the home plate 

Summary of Contents for H240













































Reviews:

No comments

Brands by name

Popular brands

Load more brands