background image

SATELLINE-3AS and SATELLINE-3ASd

1

IMPORTANT NOTICE

IMPORTANT NOTICE

This manual is copyrighted by SATEL with all rights reserved. SATEL is an abbreviation for SATEL

OY. OY is an abbreviation for shareholders company according to Finnish law. No part of this
publication may be reproduced, transmitted, transcribed, stored on a retrieval system or

translated into any other language or computer language, in whole or part, in any form or by

means, whether it be electronic, mechanical, magnetic, optical, manual or otherwise without the
prior written consent of SATEL.

SATEL reserves the right to make changes to its products or to discontinue any product or service
without notice, and advises its customers to obtain the latest information available to verify that

the information relied on is current.

SATEL’s software is provided ‘as is’. All warranties and representations of any kind with regard to

the software are hereby disclaimed, including the implied warranties of merchantability and
fitness for a particular purpose. Under no circumstances will manufacturer or developer of the

software be liable for any consequential, incidental, special or exemplary damages even if
apprised of the likelihood of such damages occurring. Title to the software and all copyrights and

proprietary rights in the software shall remain with SATEL. You may not transfer, sub-license, rent,

lease, convey, copy, modify, translate, convert to another programming language, decompile or
disassemble the software for any purpose without SATEL’s prior written consent.

SATEL’S PRODUCTS ARE NOT DESIGNED, INTENDED, AUTHORIZED, OR WARRANTED TO
BE SUITABLE FOR USE ON LIFE-SUPPORT APPLICATIONS, DEVICES OR SYSTEMS OR OTHER

CRITICAL APPLICATIONS.

Salo, FINLAND 1999

Summary of Contents for SATELLINE-3AS VHF YM5000





























































Reviews: