SANY SRT45 Safety, Operation And Maintenance Manual Download

Page: 67 / 286

Safety

Safety, Operation and Maintenance Manual

2-41

SRT45 Off-Highway Truck

2.3.5 Towing

●

When towing a damaged machine, improper
operation or use of unacceptable wire cable
could lead to serious accident:

●

Never tow the machine on a slope.

●

Wear protective gloves and a had hat when
using wire ropes.

●

Check the strength of wire cable and make
sure it could bear the weight of machine.

●

Never use ropes with broken wires (A),
reduced diameter (B) and twisting (C). Such
ropes may break when towing.

●

Never stand between the towing machine and
the towed machine during towing operation.

●

Operate the machine slowly. Never add load
to the wire cable suddenly.

Fig. 2.3-18

Courtesy of Machine.Market

Summary of Contents for SRT45































































































































































































































































































Search results

Summary of Contents for SRT45

Reviews:

Related manuals for SRT45

Brands by name

Popular brands

SANY SRT45, Safety, Operation And Maintenance Manual

Search results

Summary of Contents for SRT45

Reviews:

Related manuals for SRT45

Brands by name

Popular brands