SANY SRT45 Safety, Operation And Maintenance Manual Download Page 5 | Manualshive

Page: 5 / 286

background image

Safety, Operation and Maintenance Manual

SRT45 Off-Highway Truck

Exemption Clauses

SPECIFIC DECLARATION

Mining truck is a critical earth/rock moving machine with high traffic ability,which is mainly

distributed to coal, iron ore, limestone, quarry,hydropower...
Sany assumes no responsibility for consequences caused by the following factors:

●

Misuse of the truck due to failure to observe the information provided hereunder in this
manual;

●

Unauthorized restructuring or modification to the truck;

●

Use of non-genuine parts, or untested or unapproved parts or tools.

●

Machine failure or damage resulted from natural disasters (such as earthquake,
typhoon,etc.), wars and other force majeure.

●

Sany cannot anticipate all potential hazards that may occur on work site. Therefore, dump
truck operator and owner shall attach great importance to the issue of safety.

●

Local government may impose higher standards for use of a dump truck. If local regulations

have conflicts to the safety rules described herein, whichever the stricter applies.

Obligations of Sany

●

Offer quality truck along with correct information.

●

Abide by after-sales service commitment and keep a record for all maintenance work and
repair work.

●

Provide training for truck operators and service persons as required.

Obligations of owners or authorized persons

●

Only trained personnel who fully understand the Parts Book and the Safety, Operation and
Maintenance Manual are allowed to operate and service the dump truck.

●

Make sure that the truck operator and service person are qualified for this job and know their

responsibilities.

●

Regularly inspect the safety awareness of related persons at work.

●

Should any fault threatening safety occurs, shut down the truck immediately.

●

Sany service personnel have the right to carry out safety inspection to the truck when
required.

●

Besides the checks specified by Sany, local laws and regulations on truck shall also be
observed.

●

Ensure timely maintenance and repair of the dump truck.

●

Make a detailed plan for proper use of the dump truck.

Courtesy of Machine.Market

«
...
3
4
5
6
7
...
»

Summary of Contents for SRT45































































































































































































































































































Reviews:

No comments

Related manuals for SRT45

Brand: Shop Tuff Pages: 9

Brand: Clark Pages: 108

Aluminum LE Series

Brand: Powermate Pages: 54

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands