SANY SRT45 Safety, Operation And Maintenance Manual Download | Manualshive

Page: 99 / 286

background image

SRT45 Off-Highway Truck

3-13

Safety, Operation and Maintenance Manual

3.10.3 Parking brake

Pushing  the  switch  in  will  apply  the  spring
operated parking brakes within the rear brake
assemblies  and  the  service  brakes  at  all
wheels.  The  parking  brake  indicator  on  the
combination  instrument  will  illuminate  when
the control is pushed in. Push the switch at top
to release the brakes.

WARNING

Always apply the parking brake before
leaving the operator's seat.

3.10.4 Emergency brake

Pushing the control switch in an emergency.
To release the brakes, turn the control
clockwise.

Note:

Try to avoid using the control switch.

For normal braking the service brake pedal
should be employed.

3.10.5 Retarder

Refer  to  Fig3-11,  this  truck  is  equipped  with
two  retarders:  the  transmission  retarder  and
the rear disk brake retarder. The handle (2) is
used  to  control  the  rear  disk  brake  retarder.
The transmission retarder switch (1) is used to
control the transmission retarder.
Retardation  is  the  term  used  for  applying  a
continuous  braking  force  to  hold  the  truck
to  a  safe  steady  speed  when  descending
grades.  The  retarder  may  be  used  anytime
to slow down. If additional braking is required
apply  the  service  brakes. The  retarder  is  not
meant  for  bringing  the  machine  to  a  halt,  or
for  sudden  deceleration  -  the  service  brakes
should be employed for this purpose.
When  the  retarder  is  applied,  the  '  Retarder
Indicator  Light  '  on  the  instrument  panel  will
illuminate  and  an  orange  coloured  warning
indicator at the rear of the truck will illuminate
to warn following trucks.

1

2

Fig 3.11

Controls and Operating

Courtesy of Machine.Market

«
...
97
98
99
100
101
...
»

Summary of Contents for SRT45































































































































































































































































































Reviews:

No comments

Related manuals for SRT45

Brand: W&C Pages: 24

Brand: KION Pages: 210

Brand: HELI Pages: 82

Brand: HELI Pages: 90

Brand: Big Joe Pages: 114

Brand: EKKO Pages: 27

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands