SANY SRT45 Safety, Operation And Maintenance Manual Download Page 135 | Manualshive

Page: 135 / 286

background image

SRT45 Off-Highway Truck

4-9

Safety, Operation and Maintenance Manual

5.  Check  the  instrument  panel;  the  engine
“maintenance”, “warning”, and “stop” indicators
shall  flash  for  several  seconds  and  then
extinguish;  the  “Alternator  Charging”  and
“transmission  fault”  indicators  shall  be
constantly  on;  “transmission  state”  indicator
show red, “engine state” and “vehicle monitor
system  state”  indicators  show  green,  no
buzzer alarm (see Fig4-16).

1.Engine stop indicator

2.Engine

maintenance indicator

3.Engine warning indicator

4.

Transmission fault indicator

5.Alternator charging indicator

6. Press horn control to sound horn. (see Fig
4-17).
Caution

:

Always sound horn before starting

engine or operating anycontrol.

7.  Turn  key  further  clockwise  against  spring
pressure  to  position  'II'  to  crank  the  engine.
Release  the  key  as  soon  asthe  engine  starts

firing.

Caution

:

Never crank the engine more than

30 seconds continuously. Allowstarter(s) at
least 2 minutes cooling time between cranking
periods to avoid overheating. (see Fig4-18).

8.Check the engine oil pressure gauge. Within
10  to  15  seconds  at  engine  idle,the  gauge
needle  should  rise  into  the  white  zone.  If  the
needle  does  not  rise  within  15  seconds,  shut
off the engine and do not operate until the fault

is identified and corrected. (see Fig 4-19).

9.  Observe  the  engine  water  temperature
gauge. After  a  few  minutes  running  time  at
moderate  load  and  varying  speed,  the  gauge
needle  should  be  in  the  white  zone.  If  the
needle  moves  into  the  red  zone,  the  engine
is  over  heated  and  should  be  shut  down

Fig 4.16

Fig 4.17

Fig 4.18

Fig 4.19

Horn contorl

P

！

Engine water temperature gauge

Engine pressure
gauge

P

1 2 3

4

5

！

！

Operating the Truck

Courtesy of Machine.Market

«
...
133
134
135
136
137
...
»

Summary of Contents for SRT45































































































































































































































































































Reviews:

No comments

Related manuals for SRT45

Zaptruck-XL 2009

Brand: Zap Pages: 60

PROMASTER Cargo Van 2019

Brand: RAM Commercial Pages: 164

Brand: U-Line Pages: 3

Brand: Magliner Pages: 5

Brand: Jerr-Dan Pages: 78

Brand: LOAD KING Pages: 18

LEGACY 3 Series

Brand: LOADMASTER Pages: 25

Brand: Hyundai Pages: 232

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands