S&P TEMPEST HVLS Installation, Operation And Maintenance Manual Download

Page: 34 / 40

TROUBLESHOOTING

Set fan controller to 75% and “FWD”

Does the fan spin?

Is the LED light

blinking?

Can the speed vary from

0-100% properly?

Switch the fan to

“REV”. Allow it to ramp

down and back up.

Does it spin in reverse?

Yes

Check incoming power supply

and compare to fan rating label.

Please note all delta power

configurations are incompatible with

S&P fans

Is the input voltage correct?

Fix incorrect

wiring.

Is the fan making any

noise?

End of troubleshooting.

Yes

Check splices and wiring

at the controller.

Is the Wiring correct?

Fix incorrect wiring.

Yes

Check controller wiring sheet.

Is the wiring correct?

Fix incorrect wiring.

Yes

Check all brackets and bolts. Ensure bolts are torqued to the proper

rating and brackets are free to spin without collisions.

KEY

Start

Question

Process

Question

Solution

Consult factory.

Yes

Continued on page 35

Consult factory.

Summary of Contents for TEMPEST HVLS









































Search results

Summary of Contents for TEMPEST HVLS

Reviews:

Related manuals for TEMPEST HVLS

Brands by name

Popular brands

S&P TEMPEST HVLS, Installation, Operation And Maintenance Manual

Search results

Summary of Contents for TEMPEST HVLS

Reviews:

Related manuals for TEMPEST HVLS

Brands by name

Popular brands