SANCH S3800C Series, User Manual

Page: 77 / 105

７４
Type
Setti-
ng
Type
Setti-
ng
For adjusting cumulative running time
(resettable) in replacement (In 10 hours)
０４． ４８
－
04
Advanced functions Parameters
Control Method
Setting Range
V/f
Wit-
hout
PG
PG
V/f
PG
Para-
meter
Parameter
Functions
Fact-
ory
Defa-
ult
Torque
control
×
○ ○ ○ ○
Cumulative run time
of capacitors on PCB
○ ○ ○ ○ ○
0.0~10.0s
０４． ４９
０．０
Starting Mode (Auto
search delay time 1)
○ ○ ○ ○
×
○ ○ ○ ○
×
×
0.0(canceled)
，
0.1~500.0Hz
０４． ５０
Non-linear V/f Pattern
1 (Frequency)
○ ○
× × ×
0~ 500V: AVR action (440V series)
0~ 240V: AVR action (220V series)
０４． ５１
Non-linear V/f Pattern
1 (Voltage)
○ ○
× × ×
0.0(canceled)
，
0.1~500.0Hz
０４． ５２
Non-linear V/f Pattern
2 (Frequency)
○ ○
× × ×
０．０
１０
0~500V: AVR action (440V series)
0~240V: AVR action (220V series)
0.00~6000s
0~100%
0: take 0.00Hz as the initial frequency.
1: take the final frequency command value as
the initial frequency in the last UP / DOWN
control
０４． ５３
Non-linear V/f Pattern
2 (Voltage)
○ ○
× × ×
０
０４． ５４
Jogging acceleration
time
０４． ５５
Jogging deceleration
time
０４． ５６
Deceleration time for
forced stop
○ ○ ○ ○
×
○ ○ ○ ○
×
０４． ５７
1
st
S-curve acceleration
range (Leading edge)
○ ○ ○ ○
１０
×
０４． ５８
2
nd
S-curve acceleration
range (Trailing edge)
○ ○ ○ ○
１０
× ０４． ５９
1 st S-curve deceleration
range (Leading edge)
○ ○ ○ ○
１０
× ０４． ６０
０４． ６１
2
nd
S-curve deceleration
range (Trailing edge)
UP / DOWN control
initial frequency setting
selection
○ ○ ○ ○
１
×
○ ○ ○ ○
０
×
○ ○ ○ ○
１．６
× × ×
○ ○
0: limit by 00.16 (Frequency limiter: Low) and
continue to run
1: If the output frequency lowers below the
one limited by 00.16(Frequency limiter: Low),
decelerate to stop the motor.
０４． ６３
Frequency lower
limiter action selection
0.0: Depends on 00.16 (Frequency limiter,
Low) 0.1 to 60Hz.
０４． ６４
Frequency lower limit-
er lower action value
０
× ×
○ ○ ○
0: Valid only at constant speed running
1: Valid in all modes
０４． ６７
Automatic energy
saving operation
mode selection
０
× × ×
○ ○
0: valid in acceleration and deceleration;
valid at base frequency or above
1 : invalid in acceleration and deceleration;
valid at base frequency or above
2: valid in acceleration and deceleration;
invalid at base frequency or above
3: invalid in acceleration and deceleration;
invalid at base frequency or above
０４． ６８
Slip compensation 1
Operating conditions
selection
０．０
× × ×
○ ○
0.0(canceled)
，
0.1~500.0Hz
０４． ６５
Non-linear V/f Pattern
3 (Frequency)
０
× × ×
○ ○
0~500V: AVR action (440V series)
0~240V: AVR action (220V series)
０４． ６６
Non-linear V/f Pattern
3 (Voltage)