Samsung SVR-1630 User Manual Download Page 29

Page: 29 / 78

오류

스타일이

정의되어

있지

않습니다

SVR-1630

Samsung Techwin CO.,Ltd.

2004.07.2001 (v 1.0)

Time Zone

Select the time zone using the arrow keys on the front of the SVR-1630. Each time the arrow buttons are

pressed, the time zone is changed. (To go to the previous menu, press the [ESC] button on the front. This

operation applies equally to the OSD menu.)

Daylight Saving

This menu is interlocked with the time zone setting menu. That is, the menu is activated only when a

region where daylight saving time has been applied in the time zone setting menu. The regions where

daylight saving time is applied are programmed in the same way as the time zone in MS Windows. In this

manual, when the SVR-1630 is installed in regions where daylight saving time is applied, the relevant

daylight saving time is set using the Left and Right keys.

Sync with NTP

Sets whether to synchronize the time with the NTP (Network Time Protocol) server.

<Note>

See the paragraph “5. 7.6.5 NTP Setup” in the section 5.7.6 Network Setup for more details about NTP.

Summary of Contents for SVR-1630















































































Search results

Summary of Contents for SVR-1630

Reviews:

Related manuals for SVR-1630

Brands by name

Popular brands

Samsung SVR-1630, User Manual

Search results

Summary of Contents for SVR-1630

Reviews:

Related manuals for SVR-1630

Brands by name

Popular brands