background image

 

 

오류

스타일이

 

정의되어

 

있지

 

않습니다

.

 

SVR-1630

Samsung Techwin CO.,Ltd. 

2004.07.2001 (v 1.0) 

75

2.  Use an IP Address in a Local Network 

2.1 Executive 

Summary 

When using the Internet, you connect to servers in other locations, receive information and exchange e-

mails using an IP address. You can’t get access to the Internet without an IP address. 

 

At present, the public IP used worldwide is limited. There are 5 kinds of network holding multiple IPs 

from Class A to Class E. In particular, the most common network is the Class C network. 

 

2.2  IP Configuration and Network Class 

1) IP Configuration 

                                                                      (xxx: 0 – 255) 

 

 

2) Network Class 

Classs A

: holds all IPs with numbers from 0 to 127 for X1. 

- Network ID: X1 

- Host ID: X2, X3, X4 

- The Class A Networks available in the world are 128 in total. 

 

Class B:

 holds all IPs with numbers from 128 to 191 for X1. 

- Network ID: X1, X2 

- Host ID: X3, X4 

- The Class B Networks available in the world are 65,534 in total. 

 

Class C

: holds all IPs with numbers from 192 to 223 for X1. 

- Network ID: X1, X2, X3 

- Host ID: X4 

- This class is the most commonly used IP address. The Class C Networks available in the world 

are 2,097,152 in total. 

 

Class D

: holds all IPs with numbers from 224 to 239 for X1. 

- This is for Multicast and general users don’t use this network. 

 

Class E:

 holds all IPs with numbers from 240 to 255 for X1. 

- This network is not currently used. 

xxx xxx xxx xxx 

X1 X2 X3 X4 

 

Summary of Contents for SVR-1630















































































Reviews: