Samsung SVR-1630 User Manual Download Page 54

Page: 54 / 78

SVR-1630

오류

스타일이

정의되어

있지

않습니다

2004.07.2001 (v 1.0)

Samsung Techwin CO.,Ltd.

5.7.6 Network

Setup

There are 5 sub-menus; Network, xDSL, SWR, Port Settings, and NTP Settings

5.7.6.1 Network

When the SVR-1630 is connected to a network, the relevant network information is set in this menu.

Type

Sets the type (Ethernet/xDSL) of network line connected to the SVR-1630. When the SVR-1630 is

connected to a private line, cable modem or LAN, set to “Ethernet”.

When the SVR-1630 is connected to an xDSL line with the PPPoE method, set to “xDSL”. However, if

an xDSL line is connected, but not with PPPoE, set to ‘Ethernet’.

DHCP

Activates the DHCP function when the DVR is automatically received IP from the DHCP server.

‘DHCP’ is used in LAN environments where the DHCP Server is activated. For mid-range and large

operations, the DHCP Server is operated with a LAN. For small operations, the NAT (Network Address

Translation) function of the HUB is generally used.

IP Address, NetMask, and Gateway Address, DNS

Sets the IP address, Network Mask, Broadcast address, Gateway address and DNS address.

Summary of Contents for SVR-1630















































































Search results

Summary of Contents for SVR-1630

Reviews:

Related manuals for SVR-1630

Brands by name

Popular brands

Samsung SVR-1630, User Manual

Search results

Summary of Contents for SVR-1630

Reviews:

Related manuals for SVR-1630

Brands by name

Popular brands