manualshive.com logo in svg

SAF P89, Service Manual, Page: 26 / 28

Share
Download
SAF P89 Service Manual Download Page 26

26

XL-SA20018UM-en-US Rev H · 2017-12-14 · Amendments and Errors Reserved · © SAF-HOLLAND, Inc., SAF-HOLLAND, HOLLAND, SAF, and logos are trademarks of  

SAF-HOLLAND S.A., SAF-HOLLAND GmbH, and SAF-HOLLAND, Inc.

PROBLEM

POSSIBLE CAUSE

POSSIBLE REMEDY

Grabbing brakes

Contaminants on brake lining

Replace brake pads

Brake out of adjustment

Adjust brake/repair or replace automatic adjustment device as necessary

Warped brake rotor 

Machine or replace brake rotor 

Damaged brake chamber

Replace brake chamber

Damaged brake assembly

Replace or repair brake assembly

Unequal brake balance or timing

Repair brakes as necessary

Anti-Lock Brake System malfunction

Refer to ABS manufacturer's service literature

Excessive heat cracks in rotor  Brake out of adjustment

Adjust brake/repair or replace automatic adjustment device as necessary

Overly aggressive braking

Instruct/train driver in proper brake use

Unequal brake balance or timing

Repair brakes as necessary

Anti-Lock Brake System malfunction

Refer to ABS manufacturer's service literature

Damaged brake chamber

Replace brake chamber

Damaged brake assembly

Replace or repair brake assembly

Torque Specifications

Summary of Contents for P89





























Reviews:

No comments