manualshive.com logo in svg

SAF P89, Service Manual, Page: 25 / 28

Share
Download
SAF P89 Service Manual Download Page 25

25

XL-SA20018UM-en-US Rev H · 2017-12-14 · Amendments and Errors Reserved · © SAF-HOLLAND, Inc., SAF-HOLLAND, HOLLAND, SAF, and logos are trademarks of  
SAF-HOLLAND S.A., SAF-HOLLAND GmbH, and SAF-HOLLAND, Inc.

Torque Specifications

PROBLEM

POSSIBLE CAUSE

POSSIBLE REMEDY

Brakes will not release

Disc brake caliper bound up 

Lubricate or replace brake caliper 

Brake hoses restricted

Replace hoses

Brake control valve restricted/inoperable

Repair/replace control valve

Brake out of adjustment

Adjust brake/repair or replace automatic adjustment device as necessary

Damaged brake chamber

Replace brake chamber

Damaged brake assembly

Replace or repair brake assembly

Supply air interrupted

Open glad hand cut-out cock or push brake control valve in

Supply line improperly coupled

Properly couple supply air line

Brake pads frozen to rotor in cold weather

Warm brakes 

No brakes or insufficient brake 
performance

Service air interrupted

Open glad hand cut-out cock

Service air line improperly coupled

Properly couple service air line

Brake hoses restricted

Relieve restriction or obstruction or replace hoses

Brake control valve restricted/inoperable

Repair/replace control valve

Brake out of adjustment

Adjust brake/repair or replace automatic adjustment device as necessary

Damaged brake chamber

Replace brake chamber

Damaged brake assembly

Replace or repair brake assembly

Dragging Brakes/Slow brake 
application or release timing

Brake hoses restricted

Relieve restriction or obstruction or replace hoses

Brake control valve restricted/inoperable

Repair/replace control valve

Brake out of adjustment

Adjust brake/repair or replace automatic adjustment device as necessary

Damaged brake chamber

Replace brake chamber

Damaged brake assembly

Replace or repair brake assembly

Dog Tracking

Axle not properly aligned

Align axle

Slider assembly racked or not aligned properly Repair or replace slider assembly
Frame bent or not aligned properly

Repair or align frame

Damaged suspension component

Repair or replace suspension component

Bent axle

Replace axle

Uneven tire wear

Improper tire inflation

Inflate tire to proper pressure

Loose wheel stud nuts

Inspect for and repair any resultant wheel end damage and  
tighten properly

Improper wheel bearing adjustment

Inspect for and repair any resultant wheel end damage and  
adjust properly

Axle not properly aligned

Align axle

Slider assembly racked or not aligned properly Repair or replace slider assembly
Frame bent or not aligned properly

Repair or align frame

Damaged suspension component

Repair or replace suspension component

Bent axle

Replace axle

Mismatched tire sizes

Properly match tire sizes

Unequal brake balance or timing

Repair brakes as necessary

Overly aggressive braking

Instruct/train driver in proper brake use

High speed turns

Instruct/train driver in proper vehicle speeds

High level of side scrub

Instruct/train driver in proper vehicle maneuvering

Anti-Lock Brake System malfunction

Refer to ABS manufacturer’s service literature

18. Troubleshooting Chart 

(SAF-HOLLAND

®

 suspensions equipped with disc brake axles)

Summary of Contents for P89





























Reviews:

No comments