rotork Insight 2 Manual Download Page 53 | Manualshive

Page: 53 / 94

background image

53

6.9 Option Control

6.9.1 Option Source Selection

Source 1 Control Type

Configure the source 1 control type from a list of fitted control options.

Source 2 Control Type

Configure the source 2 control type from a list of fitted control options.

Remote Source Selection

This is where the source for remote control is selected. The options for source selection are:
Hardwired Control: The actuator can be controlled by hardwired remote controls.
Source 1 Option Control: The actuator is controlled by the network selected in Source 1.
Hardwired Switched Source 1 Control: The actuator can be controlled by either hardwired remote
controls or Source 1. A remote switch must be used to change between control sources.
Source 1 Switched Source 2 Control: The actuator can be controlled by either network selected in
source 1 and source 2. A remote switch must be used to change between control sources.
Remote Control Disabled: The actuator will not respond to remote controls.

«
...
51
52
53
54
55
...
»

Summary of Contents for Insight 2































































































Reviews:

No comments

Related manuals for Insight 2

Brand: Raytech Pages: 21

Brand: Teac Pages: 2

Brand: laerdal Pages: 2

Brand: AcceleDent Pages: 3

Brand: Zero 88 Pages: 32

Brand: GARANT Pages: 239

Brand: p-light Pages: 36

Brand: ParaBody Pages: 5

Brand: Nektar Pages: 12

Brand: Quincy Pages: 31

Lyme FIA Sofia 2

Brand: Quidel Pages: 49

Brand: Quest Leisure Products Pages: 12

Brand: Raytec Pages: 60

Brand: +GF+ Pages: 2

Unity for Pro-Flex Pivot

Brand: Össur Pages: 40

ICELOCK 234 LANYARD

Brand: Össur Pages: 94

Brand: Össur Pages: 115

Brand: Össur Pages: 253

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands