rotork Insight 2 Manual Download Page 87

Page: 87 / 94

8.8 Actuator Statistics

8.8.1 Number of Times Open Limit Reached

For indication only, shows the number of times the actuator has reached its open limit.

8.8.2 Number of Times Close Limit Reached

For indication only, shows the number of times the actuator has reached its closed limit.

8.8.3 Time Spent Moving Open (sec)

For indication only, shows the time the actuator has spent moving in the open direction.

8.8.4 Time Spent Moving Closed (sec)

For indication only, shows the time the actuator has spent moving in the closed direction.

8.8.5 Number of ESD Events

For indication only, shows the number of ESD events that have occurred.

8.8.6 Number of Motor Starts

For indication only, shows the number of motor starts experienced by the actuator.

8.8.7 Number of Accumulator Recharges

For indication only, shows the number of times the accumulator has been recharged.

Summary of Contents for Insight 2































































































Search results

Summary of Contents for Insight 2

Reviews:

Related manuals for Insight 2

Brands by name

Popular brands

rotork Insight 2, Manual

Search results

Summary of Contents for Insight 2

Reviews:

Related manuals for Insight 2

Brands by name

Popular brands