Ronde & Schwarz 1424.6721K02 User Manual Download Page 29

Page: 29 / 148

Operating concepts

R&S

NRP18S-xx

User Manual 1178.3686.02 ─ 07

5 = R&S

NRP

‑

ZK8 cable

6 = Sensor input connector of the R&S

NRX

7 = R&S

NRX base unit

NOTICE!

Incorrectly connecting or disconnecting the power sensor can damage

the power sensor or lead to erroneous results. Ensure that you connect or discon-
nect the power sensor as described in

Chapter 3.4, "Connecting to a DUT"

on page 13.
Connect the power sensor to the signal source.

2. Connect the cables as shown in

Figure 5-3

Starting a measurement

For a detailed description of how to measure in this setup, refer to the user manual of
the R&S

NRX.

1. Preset the R&S

NRX and the connected R&S

power sensors.

a) Press the [Preset] key.
b) Tap "Preset".

All parameters are set to their defaults.

2. If you use the power sensor without the attenuator supplied in the delivery or with

another 2-port device, adjust the S-parameter correction. See

Chapter 8.8.4.3, "S

parameter correction"

on page 80.

Note:

Turn off all measurement signals before zeroing. An active measurement

signal during zeroing causes an error.

a) Switch off the power of the signal source.
b) Press the [Zero] key of the R&S

NRX.

c) Tap "Zero All Sensors".

4. Configure the measurement.

a) In the "Measurement Settings" dialog, select the "Measurement Type", for

example "Continuous Average".

b) Tap "Quick Setup"

> "Auto Set".

5. Switch on the signal source.

The measurement starts, and the result is displayed in dBm.

6. If necessary, perform further settings.

R&S

NRX

Summary of Contents for 1424.6721K02





















































































































































Search results

Summary of Contents for 1424.6721K02

Reviews:

Brands by name

Popular brands

Ronde & Schwarz 1424.6721K02, User Manual

Search results

Summary of Contents for 1424.6721K02

Reviews:

Brands by name

Popular brands