manualshive.com logo in svg

Ronde & Schwarz 1424.6721K02, User Manual

Share
Download
Ronde & Schwarz 1424.6721K02 User Manual Download Page 3

Contents

R&S

®

NRP18S-xx

3

User Manual 1178.3686.02 ─ 07

Contents

1 Safety and regulatory information........................................................7

1.1

Safety instructions........................................................................................................7

1.2

Labels on the product...................................................................................................8

1.3

Warning messages in the documentation.................................................................. 8

2 Welcome................................................................................................. 9

2.1

Documentation overview..............................................................................................9

2.1.1

Getting started manual....................................................................................................9

2.1.2

User manuals.................................................................................................................. 9

2.1.3

Tutorials...........................................................................................................................9

2.1.4

Instrument security procedures.......................................................................................9

2.1.5

Basic safety instructions..................................................................................................9

2.1.6

Data sheets and brochures........................................................................................... 10

2.1.7

Release notes and open source acknowledgment (OSA)............................................ 10

2.1.8

Application notes, application cards, white papers, etc.................................................10

2.2

Key features.................................................................................................................10

3 Preparing for use................................................................................. 12

3.1

Unpacking and checking............................................................................................12

3.2

Choosing the operating site.......................................................................................12

3.3

Considerations for test setup.................................................................................... 13

3.4

Connecting to a DUT...................................................................................................13

3.5

Powering the power sensor....................................................................................... 14

3.6

Connecting a cable to the host interface..................................................................15

3.7

Connecting to a controlling host...............................................................................15

3.7.1

Computer...................................................................................................................... 15

3.7.2

Base unit....................................................................................................................... 18

4 Power sensor tour................................................................................19

4.1

RF connector............................................................................................................... 19

4.2

Status information...................................................................................................... 20

4.3

Host interface.............................................................................................................. 20

4.4

Trigger I/O connector..................................................................................................20

Summary of Contents for 1424.6721K02





















































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands