Ronde & Schwarz 1424.6721K02 User Manual Download Page 84

Page: 84 / 148

Remote control commands

R&S

NRP18S-xx

User Manual 1178.3686.02 ─ 07

[SENSe<Sensor>:]IGAMma:PHASe?

Queries the phase angle of the complex input reflection coefficient

. The result is

provided in degrees. Range:

180

degrees to +180

degrees.

Example:

IGAM:PHAS?

Query

-1.02

Response

Usage:

Query only

[SENSe<Sensor>:]IGAMma:EUNCertainty?

Queries the expanded (k = 2) uncertainty of the magnitude of the complex input reflec-
tion coefficient

. Following gamma correction, the residual mismatch uncertainty

becomes so small that it is practically negligible.

Example:

IGAM:EUNC?

Query

5.000000E-03

Response

Usage:

Query only

8.8.4.6

Using the S-Parameters program

The S-Parameters program helps loading an S-parameter table into the power sensor.
The S-Parameters program is part of the R&S

NRP Toolkit, see

To start the S-Parameters program

► In the Windows start menu, select "NRP Toolkit" > "S-Parameter Update Multi".

Configuring basic measurement parameters

Summary of Contents for 1424.6721K02





















































































































































Search results

Summary of Contents for 1424.6721K02

Reviews:

Brands by name

Popular brands

Ronde & Schwarz 1424.6721K02, User Manual

Search results

Summary of Contents for 1424.6721K02

Reviews:

Brands by name

Popular brands