Ronde & Schwarz 1424.6721K02 User Manual Download Page 27

Page: 27 / 148

Operating concepts

R&S

NRP18S-xx

User Manual 1178.3686.02 ─ 07

Setup

Figure 5-2: Setup with the R&S

Power Viewer

1 = Signal source
2 = Attenuator
3 = R&S NRP18S-xx power sensor
4 = Host interface connector
5 = R&S

NRP

‑

ZKU cable

6 = USB connector
7 = Computer with installed R&S

Power Viewer

NOTICE!

Incorrectly connecting or disconnecting the power sensor can damage

the power sensor or lead to erroneous results. Ensure that you connect or discon-
nect the power sensor as described in

Chapter 3.4, "Connecting to a DUT"

on page 13.
Connect the power sensor to the signal source.

2. Connect the cables as shown in

Figure 5-2

For a detailed description, refer to

Chapter 3.7.1.1, "Simple USB connection"

on page 16.

Starting a measurement

For a detailed description, refer to the operating manual of the R&S

Power Viewer. The

manual is installed automatically during the installation of the R&S

Power Viewer.

1. Start the R&S

Power Viewer.

2. If you use the power sensor without the attenuator supplied in the delivery or with

another 2-port device, adjust the S-parameter correction. See

Chapter 8.8.4.3, "S

parameter correction"

on page 80.

3. Execute zeroing.

Note:

Turn off all measurement power signals before zeroing. An active measure-

ment signal during zeroing causes an error.

4. Switch on the test signal of the signal source.

5. Select a measurement.

6. Start the measurement.

R&S

Power Viewer

Summary of Contents for 1424.6721K02





















































































































































Search results

Summary of Contents for 1424.6721K02

Reviews:

Brands by name

Popular brands

Ronde & Schwarz 1424.6721K02, User Manual

Search results

Summary of Contents for 1424.6721K02

Reviews:

Brands by name

Popular brands