Ronde & Schwarz 1424.6721K02 User Manual Download Page 14

Page: 14 / 148

Preparing for use

R&S

NRP18S-xx

User Manual 1178.3686.02 ─ 07

To connect to the DUT

1. Ensure that the RF connector of your DUT is compatible with the RF connector of

the power sensor or attenuator.
See

Table 4-1

2. Inspect both RF connectors carefully. Look for metal particles, contaminants and

defects.

If either RF connector is damaged, do not proceed, because the risk of damaging
the mating connector is too high.
See also

Chapter 13.1, "Regular checks"

on page 138.

3. Insert the RF connector straight into the RF output of your DUT. Take care not to tilt

it.

180

NOTICE!

Risk of damaging the center pin of the RF connector. Only rotate the hex

nut of the RF connector. Never rotate the power sensor itself.
Tighten the RF connector manually.

To disconnect from the DUT

►

NOTICE!

Risk of damaging the center pin of the RF connector. Always rotate only

the union nut of the RF connector. Never rotate the power sensor itself.
If the attenuator is attached to the power sensor:

a) Carefully loosen the union nut of the RF connector at the input of the attenua-

tor.

b) Remove the sensor with the attenuator.

Normally, it is not necessary or advisable to separate the attenuator from the sen-
sor if both are operated together.

► If you use the sensor without attenuator:

a) Carefully loosen the union nut at the RF connector of the sensor.
b) Remove the sensor.

3.5

Powering the power sensor

The electrical power for the R&S NRP18S-xx is supplied over the host interface. See

Chapter 4.3, "Host interface"

on page 20.

Powering the power sensor

Summary of Contents for 1424.6721K02





















































































































































Search results

Summary of Contents for 1424.6721K02

Reviews:

Brands by name

Popular brands

Ronde & Schwarz 1424.6721K02, User Manual

Search results

Summary of Contents for 1424.6721K02

Reviews:

Brands by name

Popular brands