manualshive.com logo in svg

Ronde & Schwarz 1424.6721K02, User Manual

Share
Download
Ronde & Schwarz 1424.6721K02 User Manual Download Page 18

Preparing for use

R&S

®

NRP18S-xx

18

User Manual 1178.3686.02 ─ 07

Set up as shown in 

Figure 3-2

.

1. Connect the R&S

 

NRP

‑

ZK6 cable to the power sensor. See 

"To connect a cable to

the host interface of the power sensor"

 

on page 15.

2. Connect the power sensors to the R&S

 

NRP

‑

Z5 sensor hub. You can connect up to

four sensors.

3. Connect the R&S

 

NRP

‑

Z5 to the computer.

4.

NOTICE! 

Incorrectly connecting or disconnecting the power sensor can damage

the power sensor or lead to erroneous results. Ensure that you connect or discon-
nect the power sensor as described in 

Chapter 3.4, "Connecting to a DUT"

,

on page 13.
Connect the power sensors to the signal sources.

5. Connect the delivered external power supply unit to the R&S

 

NRP

‑

Z5 and to an AC

supply connector.

6. Connect the trigger input of the R&S

 

NRP

‑

Z5 with a BNC cable to the trigger

source (optional).

7. Connect the trigger output of the R&S

 

NRP

‑

Z5 with a BNC cable to the trigger

device (optional).

8. On the computer, start a software application to view the measurement results.

See 

Chapter 5, "Operating concepts"

, 

on page 22.

3.7.2

 

Base unit

As a controlling host, you can use an R&S

 

NRX base unit.

You can also operate the power sensor using other supported Rohde

 

&

 

Schwarz

instruments with a sensor connector. For details, see also the user manual of the
instrument.

► Establish the connection with the base unit using:

● Host interface, see 

Chapter 5.6, "R&S

 

NRX"

, 

on page 28.

Connecting to a controlling host

Summary of Contents for 1424.6721K02





















































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands