Ronde & Schwarz 1424.6721K02 User Manual Download Page 28

Page: 28 / 148

Operating concepts

R&S

NRP18S-xx

User Manual 1178.3686.02 ─ 07

5.5

R&S

Power Viewer Mobile

The R&S

Power Viewer Mobile extends the functionality of the R&S

Power Viewer to

Android-based devices, such as a smartphone and tablets.

For connecting the power sensor to USB-C type mobile phones (Android), use an
R&S

NRP-ZKC cable. It enables the R&S

Power Viewer Mobile to take power mea-

surements via the USB-C connection.

You can download the R&S

Power Viewer Mobile free of charge from the Google Play

Store.

The 1MA215 "Using R&S

NRP Series Power Sensors with Android

Handheld Devi-

ces" application note gives a detailed description on installation and features of the
R&S

Power Viewer Mobile. The application note is provided on the documentation CD-

ROM and at:

www.rohde-schwarz.com/application/nrpz

5.6

R&S

NRX

In a measurement, the R&S

NRX uses all sensor-dependent measurement functions

and displays the results. Thus, you can configure both the measurement and the
power sensor.

Required equipment

●

R&S NRP18S-xx power sensor

●

R&S

NRP

‑

ZK8 cable to connect the sensor to the R&S

NRX

●

R&S

NRX

Setup

Figure 5-3: Setup with an R&S

NRX base unit

1 = Signal source
2 = Attenuator
3 = R&S NRP18S-xx power sensor
4 = Host interface connector

R&S

NRX

Summary of Contents for 1424.6721K02





















































































































































Search results

Summary of Contents for 1424.6721K02

Reviews:

Brands by name

Popular brands

Ronde & Schwarz 1424.6721K02, User Manual

Search results

Summary of Contents for 1424.6721K02

Reviews:

Brands by name

Popular brands