Roland LEC-300 User Manual Download Page 72

Page: 72 / 150

4-4 Replacing Consumable Parts

Chapter 4 Maintenance and Adjustment

Replacing the Separating Knife

If the separating knife becomes dull, replace it with the included replacement knife.

CAUTION

Be sure to perform operations as specified by these instructions, and never touch

any area not specified in the instructions.

Sudden movement of the machine may cause injury.

CAUTION

Never touch the tip of the separating knife with your fingers.

Doing so may result in injury.

Enter the blade replacement mode.



Press

several times.



Press



Press

several times.



Press

The cutting carriage moves to a location where blade replacement is possible, and
then the screen shown in the figure appears.



Open the front cover.

Preparations are complete when this screen appears.

Replace the separating knife.



Remove the separating knife.



Install a new knife.

The knife is secured in place by the magnet.

SUB MENU

MAINTENANCE

REPLACE KNIFE

NOW PROCESSING..

FINISHED?

OPEN FRONT

COVER

Loosen the screw until it slips out.

Grasp the screw portion, and slowly pull it

out in the direction of the arrow. When do-

ing this, do not pull it back toward you.

Magnet

Positioning

groove

Summary of Contents for LEC-300























































































































































Search results

Summary of Contents for LEC-300

Reviews:

Related manuals for LEC-300

Brands by name

Popular brands

Roland LEC-300, User Manual

Search results

Summary of Contents for LEC-300

Reviews:

Related manuals for LEC-300

Brands by name

Popular brands