manualshive.com logo in svg

Roland LEC-300, User Manual

The Roland LEC-300 User Manual is the go-to resource for unlocking the full potential of this advanced printer. This comprehensive manual, available for free download at manualshive.com, provides step-by-step instructions and useful tips to maximize your printing experience. Perfect for both beginners and professionals seeking to master their Roland LEC-300.

Share
Download
background image

Contents

3

Company names and product names are trademarks or registered trademarks of their respective holders.

http://www.rolanddg.com/

Copyright © 2008-2009  Roland DG Corporation

Methods of Printing Using Gloss Ink ................................................................................................................................. 110

5-9 Saving the Printer Settings to Match the Media .................................................................111

Saving Optimized Media Settings As Preset Values ..................................................................................................... 111
Loading a Saved Preset .......................................................................................................................................................... 112
Assigning a Name to a Preset ............................................................................................................................................... 112

5-10 Making the Network Settings .......................................................................................... 113

Setting the IP Address, Subnet Mask, Etc. ....................................................................................................................... 113

5-11 Viewing Information about the Media and the System ........................................................................................ 114

Displaying the Amount of Media Remaining  ................................................................................................................ 114
Verifying the Setting for the Amount Remaining Every Time the Media Is Changed ..................................... 114
Printing the Amount of Remaining Media ...................................................................................................................... 115
Printing a System Report ....................................................................................................................................................... 116
Viewing the Serial Number, Firmware Version, and Other Information ............................................................... 116
Viewing the Network Settings ............................................................................................................................................. 117

5-12 Performing Maintenance ................................................................................................. 118

Draining Ink and Performing Internal Washing ............................................................................................................. 118
Draining Ink Remaining Inside the Machine .................................................................................................................. 118

5-13 Menu List ........................................................................................................................ 119

Main Menu .................................................................................................................................................................................. 119
Language and Unit Menu ...................................................................................................................................................... 124
Cleaning Menu .......................................................................................................................................................................... 124
Cutting Configuration Menu ................................................................................................................................................ 124

Chapter 6 What to Do If .................................................................................................................125

6-1 The Machine Doesn't Run .................................................................................................126

The Printer Unit Doesn't Run ................................................................................................................................................ 126
The Media Take-up System Doesn't Run  ......................................................................................................................... 126

6-2 Attractive Printing Is Impossible ........................................................................................127

Printed Results Are Coarse or Contain Horizontal Stripes ......................................................................................... 127
Colors Are Unstable or Uneven ........................................................................................................................................... 127
The Media Becomes Soiled When Printed ....................................................................................................................... 128
Cutting Is Misaligned or Skewed ........................................................................................................................................ 128

6-3 The Media Jams................................................................................................................129

The Media Jams ......................................................................................................................................................................... 129

6-4 The Media Cannot Be Taken Up Smoothly .......................................................................130

The Media Cannot Be Taken Up Smoothly ...................................................................................................................... 130

6-5 Media Wrinkles or Shrinks, or Feed Is Unstable ...............................................................131

Media Wrinkles or Shrinks ..................................................................................................................................................... 131
Media Feed Is Not Straight .................................................................................................................................................... 131
Media Feed Is Not Smooth .................................................................................................................................................... 131

6-6 The Print Heads Stopped Moving .....................................................................................132

What to Do First ........................................................................................................................................................................ 132
If the Heads Still Do Not Move ............................................................................................................................................. 132

6-7 If a Message Appears .......................................................................................................133

6-8 If an Error Message Appears  ...........................................................................................134

Chapter 7 Specifications

 ...............................................................................................................137

7-1 Usable Media ....................................................................................................................138

Conditions for Usable Media ................................................................................................................................................ 138

7-2 Printing or Cutting Area .....................................................................................................139

Maximum Area .......................................................................................................................................................................... 139
Maximum Area When Using Crop Marks ......................................................................................................................... 139
Media-cutoff Location During Continuous Printing .................................................................................................... 140

7-3 About the Blade  ................................................................................................................141

7-4 Locations of the Power Rating and Serial Number Labels .................................................142

7-5 Specifications

 ....................................................................................................................143

Summary of Contents for LEC-300























































































































































Reviews:

No comments

Related manuals for LEC-300

HP DesignJet Z6610 60 Manual preview
DesignJet Z6610 60
Brand: HP Pages: 80
HP Designjet T1200 series Assembly Manual preview
Designjet T1200 series
Brand: HP Pages: 20
HP 7475a Operation And Interconnection Manual preview
7475a
Brand: HP Pages: 101
HP C4507A Quick Reference Manual preview
C4507A
Brand: HP Pages: 32
HP Designjet 8000s Series Installation Manual preview
Designjet 8000s Series
Brand: HP Pages: 193
HP C4694A User Manual preview
C4694A
Brand: HP Pages: 91
HP DesignJet 650C C2858B Setting Up preview
DesignJet 650C C2858B
Brand: HP Pages: 103
HP C4705A User Manual preview
C4705A
Brand: HP Pages: 222
HP 650c - DesignJet Color Inkjet Printer User Manual preview
650c - DesignJet Color Inkjet Printer
Brand: HP Pages: 199
HP 7585B Service Manual preview
7585B
Brand: HP Pages: 197
HP 7470A Service Manual preview
7470A
Brand: HP Pages: 141
HP DesignJet 200 Service Manual preview
DesignJet 200
Brand: HP Pages: 246
HP C2858A Service Manual preview
C2858A
Brand: HP Pages: 198
HP 7470A Interfacing And Programming Manual preview
7470A
Brand: HP Pages: 230
HP Designjet 230 Service Manual preview
Designjet 230
Brand: HP Pages: 268
HP DesignJet 2000CP Service Manual preview
DesignJet 2000CP
Brand: HP Pages: 332
Ioline Summit Service Manual preview
Summit
Brand: Ioline Pages: 139
Ioline Signature5000 Operating Manual preview
Signature5000
Brand: Ioline Pages: 258

Brands by name

Popular brands

Load more brands