manualshive.com logo in svg

Roland LEC-300, User Manual

The Roland LEC-300 User Manual is the go-to resource for unlocking the full potential of this advanced printer. This comprehensive manual, available for free download at manualshive.com, provides step-by-step instructions and useful tips to maximize your printing experience. Perfect for both beginners and professionals seeking to master their Roland LEC-300.

Share
Download
background image

2-3 Loading and Cutting Off Media

38

Chapter 2  Basic Operation

Cutting Off the Media

Procedure

Close the front cover.

Make sure

lights up.

Hold down

for one second or longer

The media is cut off.
The cutoff location on the media is as shown in the figure below.

You can make the setting in the software RIP for automatic media cutoff after printing or cutting has finished. For 
information on how to make the setting, refer to the documentation for the software RIP you're using.

Important Notes on Using the Long Media Clamps

When you're using the long media clamps, be sure to set the [MEDIA CLAMP] menu item to [LONG] 

to disable media cutoff. Performing cutting the media when the long media clamps are installed causes 

interference with the separating knife, which may result in malfunction or damage to the machine.

If you want to separate the media after printing has finished, be sure to first detach the long media clamps, 

then set the [MEDIA CLAMP] menu item to a setting other than [LONG].

 P. 82, "Printing Media That Warps Easily"

Give Attention to Media Composition

 For some types of media, cutoff is not possible. 

 Some types of media may remain on the platen after cutoff. If the media remains on the platen, remove 

it by hand.

 When you cut off media while using the short media clamps, then depending on the media, it may 

come loose from the media clamps. After you cut off the media, check to make sure that the media 

has not come loose from the media clamps.

Before you're performing cutoff, never use

to pull the media back.

Unless the end of the media has been pulled out to a location to the front of the platen, cutoff may not 

be performed smoothly.

Printed portion

The media is 

cut off here.

Blade protector

Blade 

protector

The media is fed  

to the front.

Summary of Contents for LEC-300























































































































































Reviews:

No comments

Related manuals for LEC-300

Brands by name

Popular brands

Load more brands