Roland LEC-300 User Manual Download Page 45

Page: 45 / 150

2-5 If Ink Runs Out

Chapter 2 Basic Operation

If Ink Runs Out

When ink runs out, a warning beep sounds and printing pauses (unless the default settings have been changed). Pull out
the empty ink cartridge and insert a new one. Printing resumes.

Procedure



The slot number for the empty car-

tridge flashes.



Gently shake the new ink cartridge.



Pull out the empty ink cartridge and immediately insert the new one.

Important Notes on Replacing Cartridges



Be sure to replace with an item of identical type. Never mix items of different types.



Never allow the machine to stand with an ink cartridge removed. The print heads may become

clogged.



Never insert or remove a partially used ink cartridge.



Never remove an ink cartridge suddenly while the printer is in operation.



When printing is paused, the coloring at the seam may be altered when printing resumes. Before you

perform lengthy printing, check the amount of ink remaining in the ink cartridges.

WARNING

Never store ink, cleaning fluid, or discharged fluid in any of the following loca

tions.



Any location exposed to open flame



Any location where high temperature may occur



Near bleach or any other such oxidizing agent or explosive material



Any location within the reach of children

Fire may be a danger. Accidental ingestion by children may pose a health hazard.



Keep the labeled side face up.



Insert and remove slowly, one at a time.



Insert firmly, as far as it will go.

Replace with an item of identi-

cal type and color.

Summary of Contents for LEC-300























































































































































Search results

Summary of Contents for LEC-300

Reviews:

Related manuals for LEC-300

Brands by name

Popular brands

Roland LEC-300, User Manual

Search results

Summary of Contents for LEC-300

Reviews:

Related manuals for LEC-300

Brands by name

Popular brands