Roland LEC-300 User Manual Download Page 101

Page: 101 / 150

5-6 Making Various Adjustments for Cutting

Chapter 5 Feature Reference

Execute the [CUT TEST PRINT] menu item.



Press



Press

Printing like that shown in the figure is performed.

Perform a cutting test overtop the printing test.

Check the results of the cutting test and make adjustments.



Open the front cover.



Check the results of the cutting test and make adjustments.



P. 96, "Fine-tuning the Cutting Conditions"



P. 98, "Adjusting the Cutting-in Amount"



Close the front cover.

Check the results of the cutting test and make adjustments.



Use

to move the cut-

ting carriage.

Align the center of the blade with a location where you can per-
form a cutting test overtop a printing test.

CUT TEST PRINT

PERFORMING

TEST PRINT

CUT TEST PRINT

Test print

Summary of Contents for LEC-300























































































































































Search results

Summary of Contents for LEC-300

Reviews:

Related manuals for LEC-300

Brands by name

Popular brands

Roland LEC-300, User Manual

Search results

Summary of Contents for LEC-300

Reviews:

Related manuals for LEC-300

Brands by name

Popular brands