Roland LEC-300 User Manual Download Page 103

Page: 103 / 150

5-6 Making Various Adjustments for Cutting

101

Chapter 5 Feature Reference

Correcting Misalignment of the Printing and Cutting Positions

Procedure

Check the setting for the [AUTO ENV. MATCH] menu item.

Make sure the [AUTO ENV. MATCH] menu item is set to "ENABLE."



P. 85, "Executing Environment Matching Automatically"

Execute the [ADJUST BI-DIR] menu item.



Load the media.



P. 31, "Loading Media"



P. 84, "How to Load Sheet Media"



Perform bidirectional adjustment.



P. 90, "Correcting for Misalignment in Bidirectional Printing"



P. 91, "Correcting for Misalignment in Bidirectional Printing More Precisely"

Print a test pattern and cut it.



Press

several times.



Press



Press

The test pattern is printed at three locations: at the two edges and in the center.
When adjustment is needed, go on to the steps below.

CUTTING MENU

PRINT - CUT ADJ.

TEST PRINT

Printing

position

Cutting

position

Cutting position and printing

position are misaligned.

Cutting position and print-

ing position are aligned.

Printing

position

Cutting

position

Summary of Contents for LEC-300























































































































































Search results

Summary of Contents for LEC-300

Reviews:

Related manuals for LEC-300

Brands by name

Popular brands

Roland LEC-300, User Manual

Search results

Summary of Contents for LEC-300

Reviews:

Related manuals for LEC-300

Brands by name

Popular brands