Roland LEC-300 User Manual Download Page 128 | Manualshive

Page: 128 / 150

background image

126

Chapter 6 What to Do If

specifies the IP address set on the machine, that the settings have
no typing errors, and for other such problems.



Setup Guide



P. 113 "Setting the IP Address, Subnet Mask, Etc."

Did the software RIP end abnormally?

Make sure the software RIP is running correctly, then switch the
sub power switch off and back on.

Is the temperature of the room too low?

Use the machine in an environment where the temperature is
20 to 32˚C (68 to 90˚F).

The Media Take-up System Doesn't Run

Is the take-up unit cable connected?

Connect the take-up unit cable to the machine. To perform
take-up automatically during printing, also make the setting
for the AUTO switch.



Setup Guide



P. 31, "Loading Media"

The Printer Unit Doesn't Run

Is the power switched on?

Switch on the printer's main power, then press the sub power
switch and make sure the sub power switch lights up.

Is

illuminated?

Printing is not performed when

is not illuminated. Pull

back the loading lever, close the front cover, and press
.

Is the front cover open?

Close the front cover.

Is the top menu displayed?

If the top menu isn't displayed, printing doesn't start even when
data is sent from the computer. To go to the top menu, press

, then press

.



P. 39, "Getting Ready to Receive Data from a Computer"

Is

illuminated?

When

lights up, operation is paused. To resume, press

.

goes dark and printing resumes.

Has ink run out?

When printing data is sent while
the screen shown in the figure is
displayed, a message appears and a

warning beep sounds. At the same time, operation pauses. When
the ink cartridge is replaced with a new one, printing starts.



P. 43 "If Ink Runs Out"



P. 85, "Determining What Happens When an Ink Runs Out"

Is a message displayed on the screen?



P. 133, "If a Message Appears"



P. 134, "If an Error Message Appears"

Is the power cord connected?

Connect the power cord securely.

Is the Link LED lighted?

If the Link LED for the Ethernet connector is not lighted, it means
that a correct connection to the network has not been made.
Make sure the network routing is suitable. Try connecting the
computer and the machine to the same hub, or connecting
them directly using a crossover cable. If this makes it possible to
perform printing, it means the problem is in the network itself.

Are the network settings correct?

If printing is not possible even though the Link LED is lighted,
check to make sure the IP address and other such settings are
correct. The settings on both the machine and the computer
must be appropriate. Redo the settings, checking to ensure that
the IP address doesn’t conflict with the IP address for another
device on the network, that the port setting for the software RIP

1 2 3 4 5 6

6-1 The Machine Doesn't Run

Link LED

«
...
126
127
128
129
130
...
»

Summary of Contents for LEC-300























































































































































Reviews:

No comments

Related manuals for LEC-300

P6000 - Multimedia Photo Viewer

Brand: Epson Pages: 6

Stylus Pro GS6000

Brand: Epson Pages: 128

P6000 - Multimedia Photo Viewer

Brand: Epson Pages: 113

P7000 - Multimedia Photo Viewer

Brand: Epson Pages: 116

Brand: Epson Pages: 242

Stylus Pro GS6000

Brand: Epson Pages: 298

Stylus Pro GS6000

Brand: Epson Pages: 2

imagePROGRAF iPF6400

Brand: Canon Pages: 8

iPF5000 - imagePROGRAF Color Inkjet Printer

Brand: Canon Pages: 2

iPF5000 - imagePROGRAF Color Inkjet Printer

Brand: Canon Pages: 390

Brand: Hipo Technology Pages: 32

Brand: Honda Electronics Pages: 108

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands