Roland LEC-300 User Manual Download Page 66

Page: 66 / 150

4-3 Cleaning Using the Cleaning Kit

Chapter 4 Maintenance and Adjustment

Quit the manual cleaning mode.



Press

The screen shown in the figure appears.



Attach the side cover.

Press



Close the front cover.



The print-head carriage moves to the right side of the machine, and then the screen
shown in the figure appears.



Open the front cover and attach the

maintenance cover.



Close the front cover.

Press



Press

to go back to the original screen.

Perform a printing test to verify the results of the procedure.

Perform a printing test to check the results.

Perform cleaning using the machine’s cleaning feature several times when necessary.



P. 40, "Printing Tests and Cleaning"

CLOSE SIDE

COVER

CLOSE FRONT

COVER

CLEANING...

MAINTENANCE

CLEANING

W 736mm

SETUP SHEET

ROLL

CLOSE MAINTE-

NANCE COVER

Side cover

Screws

Maintenance

cover.

Screws

Hook

Screws

Summary of Contents for LEC-300























































































































































Search results

Summary of Contents for LEC-300

Reviews:

Related manuals for LEC-300

Brands by name

Popular brands

Roland LEC-300, User Manual

Search results

Summary of Contents for LEC-300

Reviews:

Related manuals for LEC-300

Brands by name

Popular brands