Rockwell Automation SLC 500 Thermocouple Selection Manual Download Page 50 | Manualshive

Page: 50 / 92

background image

50

Publication 1747-SG001D-EN-P — January 2009

1747-AIC Isolated Link Coupler

The panel-mountable isolated link coupler is used to connect SLC 5/01, SLC 5/02, and
SLC 5/03 processors to a DH-485 network. Where there are two or more SLC 500
processors on the link, one isolated link coupler is required for each processor.
When another device (DTAM or personal computer) is connected to an SLC 500
processor at a distance greater than 6.09 m (20 ft), an isolated link coupler must be
connected at each end of the link. A 1747-C11 cable is included with the coupler for
connection to the processor.

1747-UIC Universal Serial Bus to DH-485
Interface Converter

This device allows a computer with a USB port to interface to DH-485 ports on an SLC
500, MicroLogix, or other Rockwell Automation controllers and on PanelView
terminals. The 1747-UIC features a USB connector as well as both an RS-232 and an
RS-485 port. Use the RS-232 port to connect to SLC 5/03, 5/04, 5/05 (Channel 0),
MicroLogix, CompactLogix, FlexLogix, ControlLogix, PanelView 300 or higher, or
AIC+. Use the RS-485 Port to connect to SLC 5/01, 5/02, 5/03 (Channel 1), PanelView
300 or higher, or 1747-AIC.

USB to DH-485 Interface Converter
Specifications

Cat. No.

USB Power Consumption

USB Speed

DH-485 Baud Rate

1747-UIC

<100 mA (low power)

USB 1.1 (12 Mbps)

19.2 Kbps

www.aotewell.com

www.fa-market.com

[email protected]

AoteWell International.inc

[email protected]

Tel: +852-6563-2160

«
...
48
49
50
51
52
...
»

Summary of Contents for SLC 500 Thermocouple





























































































Reviews:

No comments

Related manuals for SLC 500 Thermocouple

Brand: Veeder-Root Pages: 27

Brand: Valve Concepts Pages: 18

Brand: K&K Pages: 6

Brand: LAE electronic Pages: 7

Brand: LAE electronic Pages: 2

BT300 BurnerTronic

Brand: Lamtec Pages: 48

M16/RM N.C. DN 65 EEX

Brand: Madas Pages: 44

Brand: UniPOS Pages: 51

Brand: Unipulse Pages: 126

Brand: YachtSafe Pages: 3

Brand: Gardigo Pages: 6

Brand: VAT Pages: 14

RDS17S-ELITE1-R1

Brand: D&R ELECTRONICS Pages: 12

iDual A E27 iD60

Brand: jedi LIGHTING Pages: 23

Brand: Samson Pages: 102

Brand: Dantherm Pages: 28

Brand: Lab-T Pages: 17

I/A MicroNet MN-S Series

Brand: t.a.c. Pages: 20

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands