Rockwell Automation SLC 500 Thermocouple Selection Manual Download Page 46 | Manualshive

Page: 46 / 92

background image

46

Publication 1747-SG001D-EN-P — January 2009

DeviceNet Scanner Module

The 1747-SDN scanner module enables communication between an SLC 5/02 or
higher processor and a maximum of 63 DeviceNet-compatible I/O devices. The
scanner is the DeviceNet master, enabling data transfer between DeviceNet slave
devices using the strobe and poll message mode. The SLC system supports multiple
scanners in a single-processor chassis.

The 1747-SDN module supports:

up to 150 words of input and 150 words of output data.

all standard DeviceNet communication rates.

the exchange of status and configuration data.

DeviceNet Scanner Specifications

Cat. No.

1747-SDN

Backplane Current (mA) at 5V

500 mA

Network Power Source Requirment

90 mA @ 24V dc (Class 2)

Communication Rate

125 Kbps, 250 Kbps, 500 Kbps at 24V dc (Class 2)

Isolation Voltage

30V (continuous), Basic Insulation Type
Tested at 500V ac for 60 s, DeviceNet to backplane at 24V dc (Class 2)

DeviceNet Interface (DNI)

The DNI is a smart DeviceNet-to-DF1 interface, allowing connection of DF1-
compatible devices to a DeviceNet network where the DNI functions as a DeviceNet
slave. In addition, the DNI enables the setup of a peer-to-peer communications
network on DeviceNet with other devices using DNIs, similar to a DH-485 or DH+
network.

This capability works between controllers, between PCs and controllers, and for
program upload/download. I/O and data messages are prioritized, minimizing I/O
determinism problems typically encountered when using networks that support I/O
and messaging simultaneously.

The 1761-NET-DNI features:

high-speed local control with distributed DeviceNet I/O.

support for peer-to-peer messaging between controllers, PCs, and other devices.

programming and online monitoring over the DeviceNet network.

dial-in to any other DNI-controller combination on DeviceNet (when the DNI is
connected to a modem).

DeviceNet Interface (DNI) Specifications

Cat. No.

1761-NET-DNI

Network Power Source Requirement

200 mA @ 24V dc (Class 2)

Communication Rate

125 Kbps
250 Kbps
500 Kbps

Isolation Voltage

Tested at 500V dc for 60 s

www.aotewell.com

www.fa-market.com

[email protected]

AoteWell International.inc

[email protected]

Tel: +852-6563-2160

«
...
44
45
46
47
48
...
»

Summary of Contents for SLC 500 Thermocouple





























































































Reviews:

No comments

Related manuals for SLC 500 Thermocouple

Brand: Fagor Pages: 10

Brand: Fagor Pages: 358

Brand: Fagor Pages: 556

Brand: Fagor Pages: 172

Brand: Fagor Pages: 180

Brand: Fagor Pages: 112

Master Control Unit

Brand: FaderMate Pages: 36

Brand: Hach Pages: 2

Brand: Hach Pages: 12

Brand: Hach Pages: 472

Brand: Hach Pages: 64

Brand: V2 ELETTRONICA Pages: 6

Brand: Hach Pages: 210

Brand: Watts Pages: 4

FSDrive-MV1000 Series

Brand: YASKAWA Pages: 260

Brand: YASKAWA Pages: 114

Brand: YASKAWA Pages: 20

Brand: YASKAWA Pages: 152

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands