Rockwell Automation SLC 500 Thermocouple Selection Manual Download Page 22 | Manualshive

Page: 22 / 92

background image

22

Publication 1747-SG001D-EN-P — January 2009

Module update time is dependent on the number of channels enabled and the filter
frequency, as illustrated in the table below.

Module Update Times for 1746-NI16I and 1746-NI16V

✶

Assuming all of the enabled channels have the filter frequency shown in the first column.

Module Update Time

✶

Filter
Frequency

16 Channels
Enabled

12 Channels
Enabled

8 Channels
Enabled

4 Channels
Enabled

6 Hz

630 ms

473 ms

314 ms

7 ms

10 Hz

380 ms

285 ms

190 ms

4 ms

20 Hz

194 ms

145 ms

96 ms

4 ms

40 Hz

100 ms

75 ms

50 ms

4 ms

60 Hz

69 ms

52 ms

34 ms

4 ms

80 Hz

54 ms

39 ms

26 ms

4 ms

100 Hz

37 ms

27 ms

18 ms

4 ms

250 Hz

18 ms

13 ms

9 ms

4 ms

Temperature
Modules

SLC 500 Thermocouple/mV Input Modules

All modules interface to thermocouple types J, K, T, E, R, S, B, and N, and also accept
millivolt signals that standard analog modules are not able to detect. The 1746-INT4
module also interfaces with thermocouple types C and D.

All modules provide fully-integrated cold-junction compensation (CJC) to retain
thermocouple input signal accuracy, a choice of input filter frequencies, as well as
fault diagnostics and status LEDs.

Note:

Block transfers are required in a remote I/O configuration, using a 1747-ASB

module with a PLC.

www.aotewell.com

www.fa-market.com

[email protected]

AoteWell International.inc

[email protected]

Tel: +852-6563-2160

«
...
20
21
22
23
24
...
»

Summary of Contents for SLC 500 Thermocouple





























































































Reviews:

No comments

Related manuals for SLC 500 Thermocouple

Brand: Watts Pages: 2

Brand: Galcon Pages: 32

Brand: ABC Design Pages: 38

Brand: easydriver Pages: 26

Brand: Calsense Pages: 10

Brand: ABC Design Pages: 10

Brand: ABC Design Pages: 10

Brand: Jafar Pages: 10

Brand: Yardney Pages: 8

Brand: Bartec Pages: 26

Brand: Baninni Pages: 26

Brand: V2 Pages: 48

Brand: Parker Pages: 44

Brand: Eaton Pages: 8

Brand: ABB Pages: 44

Brand: Omega Pages: 2

Brand: Zmotion Pages: 34

Wireless Blade FX Controller for Wii

Brand: Datel Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands