Rockwell Automation SLC 500 Thermocouple Selection Manual Download Page 14 | Manualshive

Page: 14 / 92

background image

14

Publication 1747-SG001D-EN-P — January 2009

Specifications

Number of Inputs
Number of Outputs
Points Per Common

Voltage Category

Operating Voltage Range

Backplane Current (mA) at 5V
Backplane Current (mA) at 24V
Continuous Current per Point
Continuous Current per Module

Combination I/O Modules

1746-IO4

1746-IO8

1746-IO12

1746-IO12DC

2

4

6

6

2

4

6

6

2

4

6

6

120V ac (Inputs)
100/120V ac (Relay Contact Outputs)

24V dc (Inputs)
100/120V ac (Relay Contact Outputs)

85…132V ac @ 47…63 Hz (Inputs)
5…265V ac @ 47…63 Hz / 5…125V dc (Outputs)

10…30V dc (Inputs)
5…265V ac @ 47…63 Hz / 5…125V dc
(Outputs)

30 mA

60 mA

90 mA

80 mA

25 mA

45 mA

70 mA

60 mA

See Relay Contact Ratings for 1746-OW4 on page 13.

See Relay Contact Ratings for 1746-OW16 on page 13.

4 A

8 A

8 A

8 A

1746-SIM Input
Simulator

The 1746-SIM Input Simulator is designed for use on 16-channel 24V dc sinking and
sourcing modules with removable terminal blocks, including 1746-IB16, 1746-ITB16,
1746-IV16, 1746-ITV16, and 1746-IN16 modules. The input simulator provides 16
switches for simulating inputs to the SLC 500.

1746 Analog I/O
Modules

Analog I/O modules feature user-selectable voltage or current inputs, backplane
isolation, removable terminal blocks, and diagnostic feedback.

The 1746-NI4, 1746-NIO4I, and 1746-NIO4V input channels are filtered to reject high
frequency noise and provide 14- to 16-bit (range-dependent) resolution.

All 4-channel analog output modules provide 14-bit resolution and a 2.5 ms
conversion rate.

The 1746-FIO4I and 1746-FIO4V modules have less input filtering and can sense
more rapidly changing inputs. However, their input resolution is only 12-bit. Because
the input filter on the 1746-FIO4I or 1746-FIO4V module may pass more electrical
noise, you should thoroughly ground and shield the input transducer, its power
supply, and cables.

The 1746-NI8 module provides high accuracy and fast analog signal conversion. The
1746-NI8, 1746-NI16I and 1746-NI16V modules are high density analog input
modules that are software configurable.

The 1746-NO8I (current output) and 1746-NO8V (voltage output) modules are high
density, analog output modules that provide 8 individually configurable output
channels with 16-bit resolution.

www.aotewell.com

www.fa-market.com

[email protected]

AoteWell International.inc

[email protected]

Tel: +852-6563-2160

«
...
12
13
14
15
16
...
»

Summary of Contents for SLC 500 Thermocouple





























































































Reviews:

No comments

Related manuals for SLC 500 Thermocouple

Brand: Datalogic Pages: 15

Brand: Jedia Pages: 12

Brand: JED Micro Pages: 10

Brand: JCM Technologies Pages: 2

Brand: M-system Pages: 103

Brand: M-system Pages: 18

Brand: M-system Pages: 7

Grafica DNE-K07

Brand: Paradox Pages: 24

Brand: Panosol Pages: 105

Brand: Pangolin Pages: 8

Brand: Sanhua Pages: 3

Brand: QED Pages: 26

Brand: Valcom Pages: 6

Brand: Parker Pages: 16

Brand: ZKTeco Pages: 2

Brand: Parker Pages: 38

Brand: Parker Pages: 2

Brand: Sabiana Pages: 60

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands