Rockwell Automation SLC 500 Thermocouple Selection Manual Download Page 38

Page: 38 / 92

Publication 1747-SG001D-EN-P — January 2009

AIFMs for 1746 Analog I/O Modules

Description

Cat. No.

I/O Module Cat. No. 1746-…
FIO
4I

FIO
4V

NI
4

NI
8

NIO
4I

NIO
4V

NO
4I

NO
4V

NR
4

NI
16I

NI
16V

Feed-through

4-channel input, output or 2-in/2-out combination with
3 terminals/channel

1492-AIFM4-3

—

6-channel isolated with 3…4 terminals/channel

1492-AIFM6S-3

—

8-channel differential 16-channel single-ended with 3
terminals/channel

1492-AIFM8-3

—

A46

Thermocouple

6-channel with 3 terminals/channel

1492-AIFM6TC-3

—

Fusible

2-channel output, 2-channel input with 24V blown fuse
indicators, test points, 5 terminals/input, 3
terminals/output

1492-AIFM4C-F-5

—

4-channel with 24V blown fuse indicators, test points, 5
terminals/input

1492-AIFM4I-F-5

—

8-channel with 24V DC blown fuse indicators, 5
terminals/channel

1492-AIFM8-F-5

—

16-channel input with 24V DC blown fuse indicators, 3
terminals/channel

1492-AIFM16-F-3

—

A46

16-channel input with 24V DC blown fuse inidcators, 5
terminals/channel

1492-AIFM16-F-5

—

4-input/4-output channel with 8 fuses and 24V blown
fuse indicators

1492-AIFMQS

—

Pre-Wired Cables for 1746 Analog I/O Modules

These

pre-wired cables

have a pre-wired RTB on one end to connect to the front of a Bulletin 1746 analog I/O module and a

connector on the other end to plug into a 20 or 40-terminal IFM. To use this table, you must first have selected an IFM from the
preceding table.

Cable Cat. No.

Standard Cable Lengths (m)

Build-to-Order Available

AIFM Connector

Mating I/O Module Cat. No.

1492-ACABLE

✶

0.5, 1.0, 2.5, 5.0 m

Yes

15-pin D-shell

1746-NI4

1492-ACABLE

✶

0.5, 1.0, 2.5, 5.0 m

Yes

15-pin D-shell

1746-NO4I, -NO4V

1492-ACABLE

✶

0.5, 1.0, 2.5, 5.0 m

Yes

25-pin D-shell

1746-NI8

1492-ACABLE

✶

0.5, 1.0, 2.5, 5.0 m

Yes

25-pin D-shell

1746-NR4

1492-ACABLE

✶

0.5, 1.0, 2.5, 5.0 m

Yes

15-pin D-shell

1746-NIO4I, -NIO4V, -FIO4I, -FIO4V

1492-ACABLE

✶

0.5, 1.0, 2.5, 5.0 m

Yes

25-pin D-shell

1746-QS

1492-ACAB

✶

A46

0.5, 1.0, 2.5, 5.0 m

Yes

25-pin D-shell

1746-NI16I, -NI16V

✶

To order, insert the code for the desired cable length into the cat. no. (005 = 0.5 m, 010 = 1.0 m, 025 = 2.5 m, and 050 = 5.0 m). Example: Cat. No. 1492-ACABLE005A is for a 0.5 m cable

that could be used to connect a Cat. No. 1492-AIFM4I-F-5 IFM to a Cat. No. 1746-NI4 I/O module.

www.aotewell.com

www.fa-market.com

[email protected]

AoteWell International.inc

[email protected]

Tel: +852-6563-2160

Summary of Contents for SLC 500 Thermocouple





























































































Search results

Summary of Contents for SLC 500 Thermocouple

Reviews:

Related manuals for SLC 500 Thermocouple

Brands by name

Popular brands

Rockwell Automation SLC 500 Thermocouple, Selection Manual

Search results

Summary of Contents for SLC 500 Thermocouple

Reviews:

Related manuals for SLC 500 Thermocouple

Brands by name

Popular brands