Rockwell Automation SLC 500 Thermocouple Selection Manual Download Page 16

Page: 16 / 92

Publication 1747-SG001D-EN-P — January 2009

4-Channel Analog I/O Modules

Cat. No.

Backplane Current (mA) at 5V

Backplane Current (mA) at 24V

Number of Inputs

Backplane Isolation

Step Response

Conversion Method

Converter Resolution

Conversion Time

Module Throughput Delay

General Input Specifications for 4-Channel Modules

1746-NI4

1746-NIO4I

1746-NIO4V

1746-FIO4I

1746-FIO4V

25 mA

55 mA

85 mA

145 mA

115 mA

150 mA

120 mA

500V ac and 710V dc withstand for 1 minute

60 ms

100

sigma-delta modulation

successive approximation

16 bit

12 bit

N/A

7.5

s every 512

s (nominal)

512

s (nominal)

1.10 ms (maximum)

✶

512

s (typical)

✶

Worst-case throughput occurs when the module just misses an event.

Cat. No.

Full Scale

Input Range

Current Input Coding
Absolute Maximum Input Voltage
Input Impedance
Resolution

Overall Accuracy
at 25 °C (77 °F)

Overall Accuracy,
0…60 °C (32…140 °F)

Overall Accuracy Drift

Gain Error at
25 °C (77 °F)

Gain Error,
0…60 °C (32…140 °F)

Gain Error Drift

Current Loop Input Specifications for 4-Channel Modules

1746-NI4

1746-NIO4I

1746-NIO4V

1746-FIO4I

1746-FIO4V

20 mA

±20 mA (nominal)
±30 mA (maximum)

0…20 mA (nominal)
for 0…30 mA (maximum)

±16,384 for ±20mA

0…2047 counts for 0…20 mA

±7.5V dc or 7.5V ac RMS
250

(nominal)

250

(nominal)

1.22070

A per LSB

9.7656

A per bit

±0.365% of full scale

±0.510% of full scale

±0.642% of full scale (maximum)

±0.850% of full scale

+79 ppm/°C of full scale

+98 ppm/°C of full scale (maximum)

+0.323% (maximum)

+0.400% (maximum)

+0.556% (maximum)

+0.707% of full scale

±67 ppm/°C

±89 ppm/°C (maximum)

www.aotewell.com

www.fa-market.com

[email protected]

AoteWell International.inc

[email protected]

Tel: +852-6563-2160

Summary of Contents for SLC 500 Thermocouple





























































































Search results

Summary of Contents for SLC 500 Thermocouple

Reviews:

Related manuals for SLC 500 Thermocouple

Brands by name

Popular brands

Rockwell Automation SLC 500 Thermocouple, Selection Manual

Search results

Summary of Contents for SLC 500 Thermocouple

Reviews:

Related manuals for SLC 500 Thermocouple

Brands by name

Popular brands