Rockwell Automation Publication KNX-TD005A-EN-P - October 2021
159
Kinetix 2090 Interface Cables
Kinetix 6000M Hybrid Cables
Kinetix 6000M hybrid cables provide power, control, and communication between the IDM power interface module (IPIM) and the integrated drive-
motor (IDM) units. Kinetix 6000M hybrid cables are available in lengths up to 25 m (82 ft). The maximum combined cable length for all axes daisy-
chained from the same IPIM module is 100 m (328 ft). Maximum length for daisy chain is reduced by IDM units with holding brakes and number of
IDM inputs used. Refer to Motion Analyzer software, version 6.00 or later, to verify that maximum daisy-chain length is not exceeded. The last IDM
unit requires a 2090-CTHP8 hybrid bus terminator (included with each IPIM module).
Typical Hybrid Cable Application
For example, in this Kinetix 6000M system, if each cable length was the maximum 25 m (82 ft), the combined cable length would be 75 m
(246 ft).
Kinetix 6000M Hybrid Cable Descriptions
Cable Cat. No.
Description
Cable Configuration
Flying-lead/Pin
Socket
2090-CHBIFS8-12AA
xx
(1)
(1) Cables are available in standard lengths of 1, 2, 3, 4, 5, 7, 9, 12, 15, 20, and 25 m (3.2, 6.6, 9.8, 13.1, 16.4, 22.9, 29.5, 39.3, 49.2, 65.5, and 82.0 ft).
From IPIM module (flying-leads) to the first IDM unit
• IPIM-end flying-leads (IF)
• SpeedTec connector, socket (S8)
2090-CHBP8S8-12AA
xx
(2)
(2) Cables are available in standard lengths of 0.5, 1, 2, 3, 4, 5, 7, 9, 12, 15, 20, and 25 m (1.6, 3.2, 6.6, 9.8, 13.1, 16.4, 22.9, 29.5, 39.3, 49.2, 65.5, and 82.0 ft).
IDM unit-to-unit
• SpeedTec connector, pin (P8)
• SpeedTec connector, socket (S8)
2090-CBKS8-16AA03
Manual brake release
• Brake release wires (BK)
• SpeedTec connector, socket (S8)
2090-CCPP8S8
Coupler cable that connects between two hybrid cables to bypass an IDM unit
• SpeedTec connector, pin (P8)
• SpeedTec connector, socket (S8)
2090-KPB47-12CF
(3)
(3) For 2090-KPB47-12CF bulkhead adapter dimensions and specifications, refer to Kinetix 2090 Interface Cables on page
• The hybrid bulkhead adapter secures cables as they pass through the cabinet
• Mating cable attaches on the other side
2090-CTHP8
Hybrid (SpeedTec) terminator
• Required on last IDM unit, pin (P8)
• Included with each IPIM module
2090-CHBP8S8-12AA
xx
Hybrid Cables
(IDM unit-to-unit)
Kinetix MDF
IDM Unit 3
Hybrid
Cable 3
2090-CHBIFS8-12AA
xx
Hybrid Cables
(IPIM module to first IDM unit)
2090-CTHP8
Hybrid Terminator
2094-SEPM-B24-S
IPIM Module
Kinetix MDF
IDM Unit 2
Kinetix MDF
IDM Unit 1
Hybrid
Cable 2
Hybrid
Cable 1
