manualshive.com logo in svg

Robe Digital Spot 3000 DT II, User Manual, Page: 91 / 124

Share
Download
Robe Digital Spot 3000 DT II User Manual Download Page 91

DigitalSpot 3000 DT II 

 

91 

 

31.7 Installing the SDI/ASI capture card

 

 

To install the SDI/ASI capture card:  
 

1.

 

Disconnect the fixture from power. 

 

2.

 

Remove both top covers of the fixture base by  

              unscrewing  14 fastening screws. 

 

3.

 

Remove the shield cover (1)  

             by loosening  the 3 screws (2). 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 
 

4.

 

Disconnect data cables from the video capture card, take card 
out of the PCI slot  and remove the S-video/Composite 
connectors  holder (3) by unscrewing  the two screws M3x10 
(4). 
 

Note:

 in the case that this connectors holder will be installed 

back on the rear panel, it is very important to keep the 
following order of the insulating and metal washers: 
1. Insulating  plastic washers (5) 
2. S-video/Composite connectors  holder (3) 
3. Insulating  plastic washers (6) 
4. Metal washers (7) 
5. M3 nuts (8)  
 

Warning:  

The S-video/Composite connectors holder has to 

be electrically insulated from the rear panel otherwise the 
capture card can be damaged. 
Check proper placing of the insulating washers. 
 
 

 

 

 

 

 

 

 

5.

 

 Screw the SDI/ASI connectors holder (9) on the rear panel with two 
screws M3x10 (4).  

 

 

 

 

 

6.

 

Remove the capture card from its packaging and gently press it 
down into the PCI slot. 

Secure the bracket of the card to the chassis by means of the M3 

screw.   

 

 

 

 

 

 

 

 

7.

 

 Connect the SDI/ASI cables to the capture card. The IN/OUT cable  
has a blue sleeve at BNC connector and the OUT cable has a red one.  

       BNC sockets on the capture card are marked 

  (OUT)  and 

 (IN/OUT). 

 

8.

 

Place back and fasten the shield cover and top covers .  

 

9.

 

 After switching the fixture on, the new capture card should be ready for operation. 

Summary of Contents for Digital Spot 3000 DT II





























































































































Reviews:

No comments