manualshive.com logo in svg

Robe Digital Spot 3000 DT II, User Manual, Page: 87 / 124

Share
Download
Robe Digital Spot 3000 DT II User Manual Download Page 87

DigitalSpot 3000 DT II 

 

87 

31.2 Replacing the projector

 

 
If you need to remove the data projector, turn the power off and disconnect the DigitalSpot 3000 DT II from the 
mains. If the projector lamp is on, wait 20 minutes until the projector has cooled. 
 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 
 
 
1. Remove both covers (1) of the fixture head (2) by loosening  
the four quarter-turn fasteners (3) on each cover.  
 
 
 
 
 
 
 

 

 

 

 

 

 

 

 

 

 
2. Remove the rear cover (4) by loosening  the four screws (5)on the plastic 
cover and the four screws (6) on the rear cover chassiss. Disconnect all 
power and data cables (7) from the rear panel of the projector. 
 
 
 
 
 
 
 
 
3. Tilt the  head  and unscrew the four screws (9) on the bottom side of the 
head that fastening the projector chassis (10) to the fixture head. 

Warning:  

The projector can fall out from the head if fastening screws (9) are missing 
from chassis.  
 
 
 
 
 
 
4.Disconnect  cable from the focus driving motor and  unscrew two 
fastening screws (8) which securing the motor and  lift off the one. 
Carefully take out the projector (11) with chassis (10)  from 
the head. 
 
 
 
 
 
 
 
 
 

Summary of Contents for Digital Spot 3000 DT II





























































































































Reviews:

No comments