manualshive.com logo in svg

Robe Digital Spot 3000 DT II, User Manual, Page: 85 / 124

Share
Download
Robe Digital Spot 3000 DT II User Manual Download Page 85

DigitalSpot 3000 DT II 

 

85 

31. Maintenance   

31.1 Replacing the lamp

 

Turn the power off and disconnect the fixture from the mains. 

If the lamp is 

hot, avoid burns by waiting for approximately 45 minutes until the lamp has cooled. 

 
 
 
 
 
 
1. Remove the bottom cover/cover with air vents/ (1) of the fixture  
head by loosening  the four quarter-turn fasteners (2).  
 
 
 
 
 
 
 
 
 
 
 
2.Loosen the two captive screws (3) on the lamp compartment cover. 
Remove the lamp compartment cover (4). 
 

 

 

 

 

 

 

 

 

 

 

 
 
 
 
 
 

 

3.Loosen the two captive screws (5) that secure the lamp. 

Notice: Do not turn the power on with the lamp cover removed. 
Do not insert your fingers between the lamp and the projector.  
The sharp edges inside the projector may cause injuries. 

 
 

 

 

 

 

 

 

 

 

 

 

 
 
 

 

4.Lift the handle (6) so that it stands up. Use the handle to slowly pull  
the lamp out of the projector. 

 

Pulling it too quickly may cause the lamp to break and 

 scatter broken glass in the projector. 
Do not place the lamp in locations where water might splash on it, 
 or near flammable materials. 
Do not insert your hands into the projector after the lamp 
 is removed. If you touch the optical components inside,  
it could cause color unevenness and distortion of the 
projected images

. 

 

3  

3 

4 

5 

6 

Summary of Contents for Digital Spot 3000 DT II





























































































































Reviews:

No comments