manualshive.com logo in svg

Robe Digital Spot 3000 DT II, User Manual, Page: 86 / 124

Share
Download
Robe Digital Spot 3000 DT II User Manual Download Page 86

DigitalSpot 3000 DT II 

 

86 

 
 
 
5.Insert the new lamp (7) into the lamp compartment and make sure 
it fits in the projector. 
Ensure the connectors are aligned. 

 

 

 

 

 

If you experience resistance, lift the lamp and start again. 
 
 
 
 
 
 
 
 
6.Tighten the screws (5) that secure the lamp. 
Ensure the handle is fully laid flat and locked in place. 

Loose screw may cause a bad connection, which could 
 result in malfunction. Do not over tighten the screws.

  

 

 
 
 
 
 
 
 
 
7.Replace the lamp cover on the projector

 

and tighten the captive screws (3).  
 

 

 

 

 

 

 

 

 

 

 

8.Switch on the fixture. 

Note: Do not turn the power on with the lamp cover removed. 

 
9. Reset the counter "Resetable Hours” in the "Lamp on Time” menu. 
 (Item “Service Menu” in the main menu) 

 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 

 

7 

5 

3 

Summary of Contents for Digital Spot 3000 DT II





























































































































Reviews:

No comments