RiTTO TWINBUS System Manual Download Page 94

Page: 94 / 197

Inst

alla

tion

Installation: Assembly, connection and start-up

Starting up

Diode flashes once = 0.5 seconds running time

Max. switching power 1 A at 24 V AC/DC.

2.6.3 Button adapter 1 4645

Assembly

Remove the TwinBus unit from the packaging.

Connection

Connect screening on incoming and outgoing lines. Connect all unused wires as screen for YR lines.

Starting up

Start-up takes place using the TwinBus unit that is intended to react to the operation of the connected customer-

Function

Activity

Result

Switching time setting

Note:

The call interface relay 1 7646 switches only when the receiver has been put down or no speech
connection is active.

Caution!

Damage to device

The button adapter is unsuitable for connecting mains voltage.

Connections

a, b

connection to bus

white

brown

green

max. 120 s

Press setting button

LED flashes *

00107-0

Summary of Contents for TWINBUS






































































































































































































Search results

Summary of Contents for TWINBUS

Reviews:

Related manuals for TWINBUS

Brands by name

Popular brands

RiTTO TWINBUS, System Manual

Search results

Summary of Contents for TWINBUS

Reviews:

Related manuals for TWINBUS

Brands by name

Popular brands