RiTTO TWINBUS System Manual Download Page 72

Page: 72 / 197

Inst

alla

tion

Installation: Assembly, connection and start-up

If necessary, please note any existing customer settings before deletion.

Program bell buttons

One-man start-up

Delete bell buttons

Back

Menu item

Setting options

Program bell buttons

Activate programming status

Delete bell buttons

Delete all door calls

Activity

Result

Activate the programming status via the menu item
Program bell buttons

Basic settings

Program bell buttons

Programming status active

Programmed door calls: x

Back with <OK>

flashes

Within one minute, press the button to be
assigned on the door station

RiTTO

acoustic signal for confirmation at
handsfree video intercom unit and
door station

Summary of Contents for TWINBUS






































































































































































































Search results

Summary of Contents for TWINBUS

Reviews:

Related manuals for TWINBUS

Brands by name

Popular brands

RiTTO TWINBUS, System Manual

Search results

Summary of Contents for TWINBUS

Reviews:

Related manuals for TWINBUS

Brands by name

Popular brands