RiTTO TWINBUS System Manual Download Page 161

Page: 161 / 197

Operation

161

Ope

rat

Optionally with switching device 1 4981, e. g. switch light.

Shown on example of subscriber 1 (TN 1).

Function

Activity

Result

Activate call memory

Disable call memory

View

call memory

Call memory

delete

Special functions switch

Pick up receiver
Press own
internal no. for
>5 s

LED flashes 1x

Pick up receiver
Press own
internal no. for
>5 s

LED flashes 2x

TN3

TN2

TN1

Pick up receiver

TN3

TN2

TN1

missed calls are
displayed

TN3

TN2

TN1

Pick up

receiver

TN3

TN2

TN1

Press own
internal no.

TN3

TN2

TN1

TN3

TN2

TN1

Fill labelling field

1 Ð 8

press button with the receiver
put down

Summary of Contents for TWINBUS






































































































































































































Search results

Summary of Contents for TWINBUS

Reviews:

Related manuals for TWINBUS

Brands by name

Popular brands

RiTTO TWINBUS, System Manual

Search results

Summary of Contents for TWINBUS

Reviews:

Related manuals for TWINBUS

Brands by name

Popular brands