manualshive.com logo in svg

Rigol DS 5000C, User Manual, Page: 70 / 122

Share
Download
Rigol DS 5000C User Manual Download Page 70

RIGOL 

Pass/fail 

The pass/fail function can monitor changes of signals and output pass or fail signals 
by judging the input signal is within the pre-defined mask or not. 
 

Figure 2-38     Table 2-23 

 
 

Menu Setting 

Comments 

Enable 
Test 

On 
Off 

Turn on Pass/Fail test 
Turn off Pass/Fail test 

Source CH1 

CH2 

Select pass/fail test on CH1 
Select pass/fail test on CH2 

Operation

 (RUN) 

■

 (STOP)

Pass/fail test stopped, press to run 
Pass/fail test running, press to stop 

Msg 
display 

On 
Off 

Turn on pass/fail information display 
Turn off pass/fail information display 

 

 

Figure 2-39 

Table 2-24

Menu Settings 

Comments 

Output Fail 

Fail + 

 

 
Pass 

 

Pass + 

Output when Fail condition detected 
Output and beep when Fail condition 
detected  
Output when Pass condition 
detected 
Output and beep when Pass 
condition detected 

Stop on 
Output 

On 
Off 

Stop test when output occur 
Continue test when output occur 

Load 

 

Load a pre-defined test mask 

Copyright 2004 Rigol Electronic 

2-44

 

User Manual for DS5000 Series 

Summary of Contents for DS 5000C



























































































































Reviews:

No comments