manualshive.com logo in svg

Rigol DS 5000C, User Manual, Page: 68 / 122

Share
Download
Rigol DS 5000C User Manual Download Page 68

RIGOL 

 

The I/O setup: 

Press UTILITY

→

  I/O Setup to enter the following menu 

 

Figure 2-35                      Table2-21                         

 

Copyright 2004 Rigol Electronic 

2-42

 
 
 
 

 

 

 

 

 

Menu

 

Display

Comments

 

RS-232 

Baud 

****** 

Set RS-232 communication 

baud rate. This function is only 

available when EM5-CM or 
EM5-COM is attached to the 

instrument 

GPIB 
Address 

**** 

Set GPIB address. This function 
is only available when EM5-CM 

or EM5-COM is attached to the 

instrument 

 

 USB 

unconnected 

Figure 2-36                      Table 2-22   

 

                             

 

 

 

 

 

 

Menu

 

Settings

 

Comments

 

RS-232 

Baud 

300 

… 

38400 

Set RS-232

 

baud rate as 

300, 2400, 4800, 9600, 

19200 or 38400. 

GPIB 

Address 

0 

… 

30 

Set GPIB address from 0 to 

30, steps by 1. 

 USB 

connected 

NOTE:  

•

 

Before install or uninstall an extension module, it must be confirmed that the

oscilloscope powers is off. 

 

 

•

 

More details could be found in the user manual for extension module.

   

 

User Manual for DS5000 Series 

Summary of Contents for DS 5000C



























































































































Reviews:

No comments