5
2. GETTING STARTED
2.1 BEFORE SWITCHING ON
Before switching the appliance on, please familiarise yourself with:
- how to isolate the appliance from the gas, water, and electricity
supplies;
- how to check and top-up – if necessary – the system water
pressure;
- any external thermostats and their functions;
- the appliance controls.
2.2 APPLIANCE CONTROLS (see fig. 1)
The appliance controls are concealed behind the front flap of
the appliance.
NOTE
The appliance frost protection is active in all the boiler modes.
The
control panel functions
can be used to vary the
temperature of the water that circulates around your heating
system and hot water cylinder.
The heating temperature range can be adjusted between 20C
- 40C (low temperature) or 40C - 80C (high temperature) this
range is configured by your installer and the default is the high
temperature range.
Refer to the main appliance status table for fault indicator and
boiler status.
2.3 LIGHTING THE BOILER
Ensure the gas and electrical supply to the boiler are
turned on.
After completing all operations required to prepare
commissioning, proceed as follows to start the boiler.
2.4 START SCREEN
When the appliance is first connected to the electrical supply,
the REC 10 may require you to set the time and date (see
2.9.1), and the appliance will enter its ‘pre-purge’ mode that
will last for several minutes. On completion of the ‘pre-purge’
phase, the appliance will enter its ‘standby’ mode unless a
heating or HW request has been made.
By pressing the
“up”
and
“down”
keys it is possible to move
the selection of the functions in this order:
-
PLANT - STATE - SET - INFO - MENU.
By pressing the
“ok”
key you can access the settings of the
selected function (except for PLANT).
The
“back”
key is inactive (except for PLANT).
The highlighted status is that which is currently selected.
18/05/2013
12:17
MENU
INFO
SET
42
°C
1.3 bar
FRI
PLANT
HOT WATER TEMPERATURE
STATE
2.5 PLANT
The PLANT menu only becomes available if additional zones
have been added and configured with this system via the
REC10 H.
In order to change zones (see above), highlight PLANT if
necessary pressing the
“up”
and
“down”
keys.
Then, pressing the
“ok”
and
“back”
keys, it will be possible
to select the other zones in this sequence (only if added and
configured with the REC10 H)
:
-
PLANT - MAIN ZONE - ZONE 1 - ZONE 2.
The TIME AND DATE, DAYLIGHT SAVINGS TIME,
LANGUAGE and BACKLIGHT settings are are related to the
appliance only.
The information contained in the INFO menu is related to the
appliance.
No domestic hot water parameters can be set if MAIN, ZONE 1
or ZONE 2 is selected.
2.6 STATE
This function can be used to set these operating modes.
Select
STATE
BOILER
or
DHW
(in WATER TANK
configuration) or
MAIN ZONE
or
HEAT PUMP
(if present).
BOILER
MAIN ZONE
STATE
HEAT PUMP
DHW
Note:
MAIN ZONE is visible in this menu only if the zone is
managed by a room thermostat.
HEAT PUMP is only visible if a heat pump is connected to the
system.
BOILER
This function can be selected in order to set the boiler’s status:
Select
STATE
BOILER
OFF
or
HOT WATER
ONLY
(SUMMER - only if water tank connected) or
HEATING
AND HOT WATER
(WINTER).
Once the selection has been validated, the display returns to
the
STATE
screen.
OFF
HOT WATER ONLY
HEATING AND HOT WATER
BOILER
OFF:
if
OFF
is selected, the system enters the standby mode,
whereby only the standby functions remain active.
SUMMER (only if water tank connected):
if
HOT WATER
ONLY
is selected, the system produces domestic hot water.
Heating is disabled.
WINTER
: if
HEATING AND HOT WATER
is selected, the
system produces domestic hot water and activates the heating
function.
DHW (ONLY IF WATER TANK CONNECTED)
By selecting this function it is possible to set the DHW status
by selecting one of the following options: AUTO or MANUAL.
The highlighted state is the one currently selected. To select
a different status, highlight it using the “up” and “
DOWN” keys
and then press the “OK” key to validate the selection. Once
the selection is validated, the display returns to the STATUS
screen. Press BACK to return to the home screen without
making any selection.
AUTO
MANUAL
DHW
Antilegio CUT OFF (only with water tank):
this function can
be interrupted in advance in two different ways:
-
set the boiler to OFF
or
-
select
STATE
DHW
ANTILEGIO CUTOFF
.
If the function is interrupted, it will be repeated at the same
time the next day, even if weekly programming is active.
BOILER
STATE
MAIN ZONE
BOILER
MAIN ZONE
STATE
DHW
STATE
DHW
ANTILEGIO CUT OFF
