Ridder RW140 Product Manual Download Page 11

Page: 11 / 52

•

The RW70/140-34 motor gearboxes are drive units to operate indirectly-operated ventilation-

systems in greenhouses and livestock houses or crop-storage buildings.

This section tells about usual configurations of motor gearboxes and operated systems. Possibly

other configurations (or applications) are applicable.
For other (different) applications, approval from

Ridder Drive Systems

is necessary.

3.4 Dimensions

The dimensions and illustrations are approximate. In this manual shown illustrations can be

different than the components and/or systems.

RW45:

H1 = 53–56 mm

H2=170–175mm

L1 = 157–168 mm

L2 = 167–204 mm

RW-L

RW-TRA

M20

RW-D

Ø25

120

Ø28

Ø25

Ø28

Ø16

157

192

200

M10X18

151
245

(6)

Ø15

70.5

Ø17.5

1.8

Ridder Drive Systems B.V.

+31 (0)341 416 854 -

+31 (0)341 416 611 -

ridder.com

Summary of Contents for RW140





















































Search results

Summary of Contents for RW140

Reviews:

Related manuals for RW140

Brands by name

Popular brands

Ridder RW140, Product Manual

Search results

Summary of Contents for RW140

Reviews:

Related manuals for RW140

Brands by name

Popular brands